↓ Skip to main content

DIY

31 posts in this category

DIY
Verba: An Offline Latin Vocabulary Trainer on a USB Stick
2026-09-12

Verba, a Latin vocabulary trainer for my son’s 1051 words, in a single HTML file that runs from a USB stick without a network. How the word list was built and how the learning engine works.

DIY
A Wireless Rocket Launch Controller on ESP32s
2026-09-10

A two-unit wireless rocket launch controller for VRO, built on ESP32-S3s with an encrypted radio link, and the case for why done properly it is safer than a long firing cable.

DIY
Fri3d Friends: A Friend Finder and Contact Swap for the Fri3d Badge
2026-07-28

A Fri3d Camp 2026 badge app that tells you when your friends are nearby over Bluetooth, swaps contact details with a button press and is set up from a phone. It also has a camp-wide game of Gotcha.

DIY
I Vibecoded My First Fri3d Camp 2026 Badge App: And You Can Too
2026-07-09

How I went from an idea to a published Fri3d Camp 2026 badge app in an afternoon with AI-assisted coding, step by step, so you can do the same.

DIY
Running the Fri3d Camp 2024 Badge on ESPHome and Home Assistant
2026-07-05

A complete ESPHome configuration for the Fri3d Camp 2024 badge, so it shows up in Home Assistant with its motion sensor, LEDs, display and battery. Covers the driver choices that were needed.

DIY
Programming the Fri3d Camp 2024 Badge with Claude Code
2026-07-04

A hands-on guide to writing your own apps for the Fri3d Camp 2024 badge with Claude Code: backing it up, the firmware model, MicroPython and a real app with the fri3d framework.

DIY
Building a Woordklok: A Dutch Word Clock
2026-07-01

Building a Dutch word clock from the DJO Amersfoort design, with a few changes of my own to the case, and tracking down why it showed the wrong time after it was finished.

DIY
Offsite Backups on a Raspberry Pi, with a Key That Lives Only at Home
2026-06-27

An encrypted offsite backup on a Raspberry Pi at a relative’s house, reached over Tailscale, whose LUKS key never leaves home. Covers the threat model, the boot unlock and a dead-man’s …

DIY
Controlling a RunCam Thumb Camera with an ESP32-C3
2026-06-25

An ESP32-C3 that controls a RunCam Thumb over its serial protocol: start recording the moment power arrives, and check and control the camera from a web page on its own Wi-Fi access point.

DIY
Peak-Shaving the Belgian Kwartierpiek with Marstek Batteries and Home Assistant
2026-06-23

Keeping the Belgian capacity tariff down with three Marstek Venus E batteries and Home Assistant: how the kwartierpiek is billed, the settings that matter and two traps I nearly fell into.

DIY
Bringing a Second-Hand Solar-Log 500 Online
2026-06-23

Getting a second-hand Solar-Log 500 to read my Platinum 3100S solar inverter over RS485 and feed its production into Home Assistant. The wiring polarity and the firmware were the real obstacles.

DIY
Turning a Cheap Yellow Display into a Home Assistant Control Panel
2026-06-19

Turning an ESP32 Cheap Yellow Display into a desk panel with ESPHome that shows the house’s power use and opens the door or garage with a tap. Four gotchas along the way.

DIY
Building a TiltBox: A Tiny Tilt-Controlled Game Console
2026-05-13

Building a TiltBox, a small wooden game console with an 8x8 LED matrix that you play by tilting it. ESP32-C3, an ADXL345 accelerometer, a home-made front panel and a few contributions back to the …

DIY
One Desk, Three Machines, One Keyboard: My Multi-Monitor Productivity Setup
2026-04-19

Seven screens across three computers on one desk, controlled with a single keyboard and mouse through InputLeap. The layout, a custom monitor stand and the cable management.

DIY
Labeling My Basement Inventory: From Herma Stickers to a Dymo LabelWriter
2026-04-16

How labelling my parts storage grew from round Herma stickers to a Dymo LabelWriter driven by a LibreOffice spreadsheet and macro, including a long fight with label orientation.

DIY
Fixing a Yamaha 9.5A pull-cord
2015-05-01

Replacing the broken pull cord on a Yamaha 9.5A outboard, including how to handle the recoil spring safely. Documented in reverse order of disassembly.

DIY
Frankengrinder
2015-04-19

Making a missing slotted bushing for a Hobbymat MD65 lathe without a mill, by mounting a grinder on the lathe to cut the slot.

DIY
Aquarium dosing pump
2015-03-30

An automatic fertiliser doser for the aquarium, made from a 230 V mechanical timer whose slow geared motor turned out to be just right for driving a syringe.

DIY
Solder reflow oven
2015-01-22

Turning a domestic oven into a PCB reflow oven with the Hobbybotics reflow controller firmware: PID temperature control, solder profiles, a display and a PC application.

DIY
Cleaning a Siemens clothes dryer
2015-01-16

A Siemens condenser dryer kept reporting a full water tray when it was empty. A very thorough clean fixed it, at a fraction of the repair quote. Photos of every step.

DIY
Camera holder
2015-01-06

A quick plywood cabinet that gives my Nikon D3000 a fixed place on the workbench, with a USB cable routed in so it can stay connected.

DIY
Electronics components cabinet
2014-11-28

A cheap plywood cabinet that stores SMD and through-hole parts in small screw-cap yoghurt-drink bottles, each with a label on the cap.

DIY
Table saw slide
2014-10-18

A sliding table for my table saw that always runs square to the blade, replacing a fence that never stayed parallel.

DIY
Pillar drill table
2014-10-14

A bigger table with a sliding precision fence for a cheap pillar drill, made from scrap multiplex and rubberwood, for drilling repeatable holes.

DIY
Snelkoppeling voor flessenspoeler
2014-10-07

A small change that lets the Blast bottle rinser click onto a standard hose quick-connector instead of being screwed onto the tap. In Dutch.

DIY
Beer rack
2014-08-15

A rack under the basement stairs that holds 23 cases of beer, built from cheap pine and sized for Duvel crates. The cases sit half on their side so every bottle can be reached without lifting a crate.

DIY
Automated brewery
2013-08-25

A small automated brewery for 28 litre batches, built around a Weck kettle and a BrewTroller controller as a cheaper alternative to a Braumeister. A photo series of the build.

DIY
Homemade malt mill
2013-01-17

A two-roller malt mill built as a metalworking exercise, with an adjustable gap so the grain is crushed fine while the husks stay mostly whole for lautering.

DIY
Building the MiniMost
2012-08-05

Building the MiniMost, a small plywood boat from a 1960s Popular Mechanics design, to put a second-hand 2 hp outboard to use. Build log in Dutch.

DIY
Homemade magnetic stir plate
2012-03-29

A stir plate for growing yeast, built around an 80 mm computer fan with PWM speed control, plus thermostat-controlled heating, in a two-level case.

DIY
Fishing raft
2011-08-05

A floating platform with a sofa bed, a tent and a barbecue that we built, took onto the river and lived on for a few days of fishing. Mostly photos.